The basic functions of the elevator and all-round needs can be purchased according to the actual needs of customers.
“ Safety first ”
1、 32 Bit Processor :
32-bit main computer plus 32-bit DSP vector frequency conversion control technology, more than 100 software and hardware interactive debugging and self-checking, to achieve multiple security protection.
2、 Fault automatic analysis :
Classified processing of fault types. If the elevator stops abnormally in a non-leveling area, in the case of safe and normal power supply, the system can run at low speed for self-rescue operation to the nearest floor to open the door, reducing the incidence of closing faults. The system has built-in clock management to record the fault information and the time of occurrence, which is convenient for troubleshooting and speeding up the troubleshooting of abnormal problems.
3、 Data network system :
Combined with CANBUS, MODBUS advanced communication technology, strong anti-interference, more than 60% less control lines than traditional elevators, and also reduce failures caused by abnormal control lines.
4、 UCMP Protection :
Unintended Car Movement Protection (UCMP), derived from the European Regulation EN81-1:1998 Amendment A3: When the elevator is in the leveling position and the door is open, if the elevator moves unexpectedly, the UCMP safety device will immediately activate the protection , Stop the elevator. Its contents include dual brake system, brake performance self-test, door lock circuit failure detection, upward overspeed protection when brake failure occurs, and protection of abnormal movement of elevator when door is opened to ensure passenger safety.（Optional）
5、 ARD Device :
When an earthquake of magnitude 4 or above occurs, the "earthquake sensor" will send out a signal immediately to stop the elevator on the nearest floor and open the door, so that passengers can evacuate as soon as possible. （Optional）
6、 Earthquake Control Operation :
When an earthquake of magnitude 4 or above occurs, the "earthquake sensor" will send out a signal immediately to stop the elevator on the nearest floor and open the door, so that passengers can evacuate as soon as possible.（Optional）
“ Intelligent control ”
7、 Switch door obstacle protection :
When the elevator door encounters abnormal obstruction during the closing process, the system will stop automatically after repeated closing for a certain number of times to avoid damage to the machine parts. If the boarding door cannot be opened normally, the elevator will automatically drive to the next floor to open the door to prevent passengers from being trapped.
8、 Automatically determine waiting time :
The system can automatically discriminate in-car call, boarding call, main floor call or barrier-free button call, and provide different waiting time for door opening to improve elevator transportation efficiency.
9、 Wrong button cancel :
When passengers in the carriage press the button on the wrong floor, they can press the button on the floor twice to cancel the call registration of the button and avoid unnecessary running services.
10、 Reverse automatic cancellation :
After the elevator runs up or down to send a car to the final floor, it will automatically remove the floor buttons that are wrongly registered in the car to avoid unnecessary running services.
11、 Button card key exclusion :
If the car call button is forced to act due to damage to the card key or external force, the elevator door will not be able to be closed. After a certain time, the system will automatically cut off the button signal, so that the elevator can close the door to continue to serve other floors.
12、 Anti-tamper function :
The system can be equipped with a weighing sensor to automatically determine the number of passengers in the car. If too many floor buttons are registered, the elevator will automatically cancel the car call on other floors in the car after running for 3 floors, avoiding unnecessary operation services.
13、 Overload full load detection :
When the passenger or the load exceeds the rated load of the elevator, the buzzer in the car will sound a warning sound and keep the elevator door open to avoid the danger of the elevator due to overloading. The system can be equipped with a weighing sensor to automatically determine the number of passengers in the car. If the load exceeds 80%, the elevator will not accept the call from the airport and will automatically pass through without stopping to avoid adding invalid running stops.
14、 Level automatic correction :
When the deviation from the ground level is greater than 1.5 cm due to the change of the load of the carriage and the extension of the steel cable, the system can automatically make fine adjustments and corrections.
15、 Arrival notification :
When the elevator is about to stop, the floor display will flash and notify passengers with an electronic bell.
Customers can also choose a "Voice Announcer" to facilitate the use of the elevator by the disabled.
16、 PARK Shutdown operation :
In commercial buildings, when the elevator management needs to stop at night or on holidays, the key switch (or computer monitoring) is used to control the elevator to return to the main floor, stop running and automatically turn off the lighting and fans.
17、 Light fan automatically shuts off :
When the elevator is not in use within the set time, the lighting and fan in the car will be automatically turned off to save electricity.
18、 Dedicated (VIP) Service :
After the dedicated (VIP) service is activated, the elevator will go directly to the VIP floor and wait for the door, providing priority service for VIPs. The display on each floor shows "dedicated", the elevator does not serve the calls of other floors temporarily, if the elevator is not used for more than 30 seconds, the elevator will automatically return to the general use state.。
19、 Special floor control :
When some floors of the elevator need to be controlled in and out, the key switch or preset specific time (or computer monitoring) can be used to suspend the service of a specific floor.(You can also purchase a credit card machine for control)
20、 Time-sharing tiered service :
In the case where multiple elevators are connected in series, the service of some floors can be preset to be cut off within a specific time, so that the elevators can concentrate on serving the floors with higher passenger capacity.
21、 Dot matrix LED display :
The 16x24 dot matrix LED display can display information in simple and easy-to-understand Chinese (or English) when the elevator is in failure, maintenance, full-load, dedicated, and fire-fighting situations to inform passengers waiting on the floor and understand the operation of the elevator. state.
22、 MIB computer monitoring :
In the management room, a PC computer is used to monitor the running status of all elevators in real time. If there is a fault or abnormality, the elevator screen will display a red warning and fault content, and an alarm sound will be issued to notify the management personnel, and the abnormal information detected will be sent. Instant record archiving as reference data for customers or elevator maintenance personnel to diagnose elevators. The detailed operation status of each elevator is displayed synchronously with dynamic graphics, such as elevator status, control status, fault information, car position, door opening and closing status, and car call status on each floor. Elevator control such as fault reset, fire recall, elevator lock and stop, special operation, floor control, elevator call to any floor, all can be operated by computer.（Optional）
“ Energy saving and carbon reduction ”
23、 PM Synchronous Motor Control :
Taking the speed of 90m/m on the 10th floor and a general residential elevator as an example, the elevator operates about 900 times a day for about 4 hours. The daily power consumption of the traditional variable frequency induction motor is about 22 kWh (the monthly electricity bill is 3,300 yuan); the daily power consumption of the synchronous motor is about 15 kWh (the monthly electricity bill is 2,250 yuan), saving 32% of electricity. (Including about 4 kWh of electricity per day when the elevator is half-standby)
This description is an estimate and is for customer reference only.。
24、 AFE power regeneration device :
When the variable frequency elevator decelerates and brakes, the electric energy fed back by the motor in the form of power generation is consumed by the way of generating heat energy by the power resistor. High-tech energy regeneration technology can feed back electricity to the building grid for other equipment to use. This system can save about 25~40% of energy. Most of the heat source of the elevator machine room comes from the power resistor. After installing the power regeneration device (hereinafter referred to as AFE), the resistor does not generate heat, and it also reduces the power consumption of the machine room exhaust fan or air conditioner.
The energy saving chart in the following example uses the old building as a general AC stepless motor, and the power consumption is calculated as 100%.
(As shown below)
Panorama Lift Purchase Notes -
If you have any questions, please call to contact our business personnel, or leave your information,
And provide your question, we will answer you as soon as possible.
Information required to purchase an elevator
1、Load capacity (number of people loaded).。
2、Elevator speed.
3、Stop the number of floors.
4、Decoration specifications. (entrance and car type)
5、Building blueprints related to elevators.
6、Elevator equipment and functional details.。
7、Power supply, voltage and frequency.